本產品采用**進口丙烯酸樹脂和**顏料經過細制研磨加工組合而成，適用于各種金屬、玻璃、陶瓷、石材、電鍍(含水電鍍)、陽極氧化鋁表面、靜電噴漆面及烤漆面等制品的絲印及移印，不需加固化劑，不需烘烤，即可獲得優異的附著力。油墨特性：1、平光(如需亮光請選擇我司JL系列)、附著力佳、耐酒精、耐化學品；2、手感好，流平性佳、面光潔；3、表面硬度好，耐沖擊性能強、抗刮傷；4、耐酒精、耐化學品程度佳；印刷：選用網目為100-420目，以120T聚酯單絲、感光膠網版計算涂覆蓋面積每公斤達35~40㎡。表干時間自然揮發5-10分鐘，實干時間在24小時以內，48小時后達**佳性能。1.用B-03專用稀釋劑**2.用718洗網水洗網。3.可選擇添加JS-9硬化劑10%用于增加油墨附著力及物理化學抗性。4.烤箱80℃烘烤30分鐘佳能更優。測試方法(完全干燥后)：1.3M膠紙粘在畫有百格的油墨表面45度角迅速拉起不脫油。2.純度99%的酒精500G力在油墨表面來回擦拭200次無脫色。使用方法：1.使用前應充分?jǐn)嚢瑁煤箅S時密封。2.攪拌時先加固化劑靜置10分鐘后，再加稀釋劑10-15%，稀釋到印刷粘度。3. 加入固化劑的油墨使用時限為4-6小時，過期請棄用，剩余油墨不可回收。4.網版塞網時可用洗網水清洗。5.不得與其它類型油墨混合使用。注意事項：1.各種物料的外觀相似，但可能會是不同的材料，客戶需先試印，確其符合要求后，再批量生產。2.在移印過程中，如出現拉絲或散開現象，可適當加入一些慢干膏即可。3.環境溫度過高，將會影響油墨原有質量。4.請遠離火源，避光保存。

Product Name: Ou Les anodic alumina dry metal [ ] series of silk screen printing ink

Product Name: Ou Les anodic alumina stem from the metal silk screen printing ink

This product adopts advanced imported acrylic resin and pigment through fine grinding senior system combination, applicable to all kinds of metal, glass, ceramic, stone, electroplating ( aqueous electroplating ), anodic alumina surface, electrostatic spray painting surface and face painting and other products and silk screen printing, without curing agent, without baking, can be to obtain excellent adhesion. Ink characteristics:1, Matt (as required. Please choose our JL Series ), adhesive force is good, alcohol resistance, chemical resistance;2, good hand feeling, leveling, good surface finish;3, surface hardness, impact resistance, strong resistance to scratching;4, alcohol resistant, chemical resistant degree preferred; printing : selection of mesh for100-420,120T polyester monofilament, photosensitive adhesive coated area screen calculation every kilograms amount to 35~ 40square meters. Surface dry time natural volatile5-10 minutes, drying time is in 24 hours,48 hours after the best performance. 1B-03special thinner open water2718wash wash water network. 3can choose to add the JS-9hardening agent10% is used for increasing the adhesion of the oil ink and physical and chemical resistance. 4to 80 DEG C baking oven30 minutes more and canon. Test method ( completely dry ) : 1.3M gummed paper in the painting has hundred grid ink surface angle of 45 degrees to quickly pulled off oil. 299% of the purity of alcohol500G force on the surface of the printing ink and wipe back and forth200 times without decolorization. Method of use:1before use should be fully stirred, use at any time after the seal. When the first and2 mixing curing agent standing for 10minutes, plus diluent10-15%, diluted to printing viscosity. 3adding curing agent ink time limit for4-6 hours, please not expired, the remaining ink unrecyclable. 4screen plug mesh can be used when washing network water cleaning. 5 may not with other types of ink mixed use. Note: 1all kinds of materials, similar in appearance, but may be of different materials, customers need to try printing, ensure its requirements, and then batch production. 2in the printing process, such as drawing or spread phenomenon, may be appropriate to add some slow dry plaster. 3the ambient temperature is too high, will affect the quality of the original ink. 4 please stay away from fire, keep out light.